Inflate Your Bicycle Tube: Get the Optimal Tire Pressure in 5 Steps

Inflate Your Bicycle Tube: Get the Optimal Tire Pressure in 5 Steps

Nothing is as effective and important for a pleasant bike ride as this correct tire pressure. We’ll show you how to correctly inflate the bicycle tube.

When you need to inflate the bicycle tube?

You get up to speed on your bike much slower driving is difficult and you have to use a lot more force? Then it’s time to check your tire pressure. Because only with one ideally inflated tube you ride your bike really comfortably. The difference is immediately noticeable. All you need is a pump to inflate the bicycle tube.

However, have tires often different types of valves. That’s why you don’t just need any equipment, but the right pump for your valve.

Inflate your bicycle tube in five easy steps

Various valves are installed on bicycle tubes. The valves differ in Dunlop valves, Schrader valves also known as auto valve, and Presta valves. Cyclists also know the Presta valve as the French valve. Depending on the variant of the valve, you will need one to inflate the tire special bicycle pump.

So, first check which valve your tires have and whether you have the right bicycle pump at hand. Below we will show you how to inflate the bicycle tube:

  1. Turn the small one metal cap of the bicycle valve. It can also be made of plastic. With the French valve, you also open the valve head slightly.
  2. Now place the bicycle pump with the appropriate hole on the valve and press the pump lightly onto the valve. One or another pump has a lever to open and close the hole. The lever is applied when it is put on and is turned over after the pump has been inserted. The valve and pump are then firmly anchored together.
  3. Now you can put it in the hose pump in air. With a floor pump you will usually notice a higher air pressure after just a few strokes. With hand pumps, on the other hand, it often takes significantly longer for the pressure to increase.
  4. If your air pump has a pressure gauge for control, you can pump the air up to the desired level Air pressure pump up. If you don’t have this instrument available, check by hand whether the pressure in the inflated tube is sufficient. To do this, simply press the side of the tire with your thumb and other fingers.
  5. Finally, set the Valve cap back up and tighten it.

It’s worth washing the caps because they get dirty over time. If you have inflated the tube and then notice that the pressure too high is, you let the air escape. Press that opened valve then with one small pin in the middle on or turn it ring around the valve easily up.

Sometimes pressing your finger on the valve helps. You can usually hear whether air is escaping by a quiet hissing sound.

Also read: Bicycle Tires Explained: Types, Structure, and Choosing the Right One.

This is how you pump the right air pressure into the bicycle tube

You are probably wondering what air pressure is right for your bike tires. We’ll give you one here assistance for the different types of bikes. The fact is that every bike is different optimal tire pressure needs. The following list are the rough ones Guide values summarized:

  • Mountain bike: approximately around 2.5 bar
  • City or trekking bike: from 3 to 4 bar
  • Road bike: about 8 bar

The Tire width has a lot of influence on the ideal air pressure. The wider the tire, the lower the recommended air pressure. On the side of the coat can you read how much cash Pressure for the bicycle tube is permitted. With an air pump with a pressure gauge you can determine how much pressure is on your hose.

To get a feel for when it’s time to measure the pressure in the bicycle tube, you can do the following remember formula: During normal use, your bike loses up to one bar of pressure per month.

Determine the correct pressure in the hose without a pressure gauge

In practice, you don’t always have the opportunity to determine the tire pressure precisely to the bar. But that’s not tragic. Simply inflate the tube until the tire above it is hard enough but can still be pressed in a little by hand. Then you have it hose inflated optimally. Nevertheless, it is recommended to determine the pressure every now and then.

This is how you make sure that the driving characteristics of your bike make it pleasant over the long term.

Protection against damage caused by low tire pressure

Are you rarely in the city, but more often on slopes off the beaten path? On a mountain bike that you ride a lot off-road, there is one low tire pressure sensible. This will help you avoid damage that occurs very quickly with sharp-edged floors.

You should never inflate mountain bike tubes with high pressure because they are then more vulnerable and will burst more quickly. Also at puncture-proof tires, the optimal tire pressure is essential so that they can develop their properties.

Must read: Bicycles with Steel Frames Ensure Trendy Vintage Style.

It is not possible to inflate the tube – what to do?

You pump air through the bike valve, but somehow it creates no pressure in the hose? First check whether you are really using the right bicycle pump for your valve. Then check whether the hose is intact or has holes through which inflated air can escape immediately. If you still haven’t found the cause, take a close look at the valve.

Often there is one damaged valve the reason for a flat bicycle tire. The Valve inserts can be changed. This is always better than having to change the bicycle tube so that the bike can roll again. If you have problems inflating the tube, any bicycle repair shop or specialist retailer can help you.

Inflating a bicycle tube at the gas station

If your bike has a Schrader valve, that too Car valve is equipped, the bicycle tube can also be inflated at the gas station. There you can also test inflate all other types of bicycle valves using an adapter. If the pump at the gas station works, but your own air pump doesn’t, it could be defective. Then you have to buy a new bike pump.

Total
1
Shares
Leave a Reply

Your email address will not be published. Required fields are marked *

Previous Post
Overview of Bicycle Brake Types

Overview of Bicycle Brake Types

Next Post
Essential Guide to Bicycle Hub Maintenance: Ensuring Smooth Rides

Essential Guide to Bicycle Hub Maintenance: Ensuring Smooth Rides

Related Posts